forumyaren.com

Home > Error Code > Vita Spa Error Code Ice

Vita Spa Error Code Ice

Contents

FL: Flow. Call for service. Do not use spa when temperature is flashing or the OH message is displayed. dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message). http://forumyaren.com/error-code/vita-spa-error-code.php

Switch closed while pump is deactivated COL: Cool condition. You will not have control over the components till after this happens. Spa has shut down. Snb = Spa is shut down. http://www.justanswer.com/pool-and-spa/7nzmu-hi-vita-spa-code-ice-pump-circulate.html

Hot Tub Error Codes

Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. System will restart when temp. Sn2 = Nonfunctional temperature sensor. ILOC = Interlock failure - possible pump or ozone spike. (---) =Unknown water temperature. (Displays when first powered up after refill).

drops. So you are saying that it never heated? SnS = Sensors out of balance. Gecko Spa Pack Error Codes Status of the heater element is unknown.

SE = Spa operating in Standard-in-Economy Mode. Balboa Error Codes * pd : Power supply, unit running on battery backup * OH : Sensors reading 112-118 Degrees * OHH : Overheat. If message comes back, call for service. https://spacare.com/spasideerrorcodes.aspx Hi limit sensor is disconnected, shorted, or spa temp is above 112° F.

No action is necessary.I CE2 = Freeze protection. Balboa Spa Control Manual Contact qualified service technician Spa Quip Error Codes * err 1 (H20) : Prime Failed * err 3 : Stuck Button * err 4 : No Water Sensor * err 5 PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. SnH Hi Limit circuit open or faulty SnS Sensors out of balance, reporting different results SnT Temperature sensor fault, circuit open or faulty SP-F1,F2 or F3 Fuse 1,2 or blown SP-HR

Balboa Hot Tub Error Codes

Heater disabled but spa operational SESH Sensor short, nonfunctional. and turn it back on. Hot Tub Error Codes Pr = When spa is first actuated, it will go into Priming Mode. Vita Spa Error Codes If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected.

Read the HTA Privacy Policy | Terms and Conditions Registration No. 06766519. this content Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when Spa has shut down. One sensor has detected 118º * OHS : Overheat. Marquis Spa Error Codes

FLO2 = Closed or shorted flow switch on system startup Dream Maker Spa Side Error Codes OH = Overheat 108° F, spa is deactivated. Water temperature has reached 118ºF. PSoL = Pressure switch open with low pump. weblink drops * HL : High limit switch tripped Dream Maker Error Codes * OH : Overheat 108° F, spa is deactivated.

In rare cases (usually warmer climates), the circulation pump may also cause overheating. Coleman Spa Error Codes Hold = Panel sensors have been pressed too many times in a short period of time. Rare system error.

HL = High limit switch tripped.

SEoP Sensor Open Circuit SEoP Sensor open or disconnected. If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. All rights reserved. Spa Command Panel Instructions Rare system error.

Heater may have to be replaced. CTI Spa Side Error Codes th1/39 = On startup indicates temperature probe problem. Spa may be partially deactivated or low speed pump (and air blower if equipped) may activate to lower temp OH, OHS, oH Overheat Condition 43-45C OHH Overheat. http://forumyaren.com/error-code/vita-spa-error-code-ps.php Spa unusable.

PSoH = Pressure switch open with high pump. Do not use spa when temperature is flashing or the OH message is displayed. err 1 (H20) Prime Failed err 3 Stuck Button err 4 No Water Sensor err 5 Overtemperature err 6 Thermal Cut Out Tripped err 7 Stuck Relay err 8 No Temperature Heater is deactivated.

Could indicate a flow problem HL High Temperature Alarm HL Temp above 118 degrees HL, HFL, HH, OHH High limit sensor reading 45-48C, or above - check flow HLoH Hi Limit Do not enter the water. Other issues that can cause these error codes one or more of the service valves is not open up all the way. Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).

Not all spa codes are errors, to inform you of trouble, but many codes are used to provide information about system mode, status or equipment operation. LOC Panel Lock; enter code to unlock control panel O3-Er Ozone error; check for operation and output OH High temperature condition, over 110ºF. Entire system is disabled. Check for proper spa water level and ensure pump is primed.

The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. If "FLO" remains check need to prime the pump(s). System will restart when temp. Ask an Expert Online.

If the water temp is more than 20 degrees below what you have it set for, it will show the ice code until the temp comes up. Water temperature has reached 118°F. Make sure that they are open.• Clean the filter(s), waterline skimmer and footwell suction for any blockage..• In extremely hot weather, check for proper cabinet ventilation.• Check for excessive filter duration.