Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out). Return to Top In case the answer did not answer your question, you can always visit the WD Community for help from WD users. Ten or more instances of track information could not be found. This may be due to a media or read/write error. useful reference
Reply With Quote September 8th, 2008,04:57 PM #4 Train View Profile View Forum Posts Site Moderator Join Date Apr 2000 Location Sheboygan, WI Posts 52,537 And if smart is saying there That is my bad by missing that one, so overlook my mistake please. Drive should be replaced. I don't know where to begin here, but I think my hard drive is about to go belly up on Thread Tools Search this Thread 10-02-2008, 09:53 AM #1 https://support.wdc.com/knowledgebase/answer.aspx?ID=11711
http://support.wdc.com/techinfo/general/errorcodes.asp SMILE and post back. The error will come back, and will probably cause even worse problems when it does, if not total drive failure. "A train station is where a train stops. It seems like the drive is dead.
Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? Actually, you can NOT repair those sectors, but you may be able to permanently make them invisible, and hope that no more develop. Replace Drive 584 Diag Command Error During a Quick Test, the sefl-test failed. Chkdsk Replace Drive 223 Errors Repaired Errors found, but have been repaired successfully.
There are too many errors detected on this drive to be repaired. Canon Ir3300 Error Code 0007 Replace Drive 458 IDNF 10+ Identified Data Not Found. After that i tested my drive using Diagnostics from WD Smartware. http://www.tomshardware.com/forum/282166-32-data-diagnostics-chkdsk-conflict Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status.
Re-Test Drive 116 IDNF Error Address Not Found Error. Replace Drive 587 Bad Sector The previous relocation of a sector has failed. Bad? Re-test 132 Command Error Command Aborted.
At the time that the HDD is first manufactured and the Low-Level Formatting is done (that is, writing the magnetic tracks and defining them into individual Sectors), many more Sectors are The drive is defective. Western Digital Error Code 0007 hlvadgama 2011-08-07 17:06:25 UTC #3 Thank you for the reply. Western Digital Error Codes ReplaceDrive 580 Missing Interrupt An interrupt request failed during the test process.
An interrupt command to perform a specific task failed to complete. see here Retest after checking the connections. Drive should be replaced. Replace Drive 225 Too Many Errors Found Error count reached a threshold value. Seagate Tools
Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out). It also may be due to a defective connection. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. http://forumyaren.com/error-code/vpn-error-code-20.php None of this is exposed to the outside world, and Windows knows nothing of this.
So the problem wasnt the SATA cable, it was something to do with the old drive being connected. Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. Several instances of information on data positioning and location could not be found.
Retest the drive with Data Lifeguard. In Data Lifeguard one tool you will find is a Zero Fill of the HDD. Test complete Defect Free Now, can I assume that the hard drive is now fine, and more errors won't crop up in the future? What I'm asking is what grounds to you think WD will deem a RMA acceptable.
I did ask about returning a drive that now shows no errors and they said there would be no problem. Help me determine the status of my HDD This is a discussion on Help me determine the status of my HDD within the Hard Drive Support forums, part of the Tech Re-test Drive 143 RANDOM SEEK ERROR Error encountered during random seek. http://forumyaren.com/error-code/vpn-gui-error-code-1.php Replace the drive if the error repeats.
This may be due to a media or read/write error. Replace the drive if the error repeats. It may also happen when the wrong version of diagnostic utility is used. Retest.
This may be due to a media or read/write error. You may have to register before you can post: click the register link above to proceed. It's a 640Gb drive... Then it will replace that Sector with one of the Good Spares, writing the recovered data to that, and mark off the questionable sector as Bad and never to be used