forumyaren.com

Home > Error Code > Wd Hdd Error Code 0223

Wd Hdd Error Code 0223

Contents

Block start at 1754626048 = 344 ms Начните с 1-ого, в Victoria for Windows: Start LBA: 34625000 End LBA: 34629000 Block size: 256 (при необходимости уменьшая до 32) Loop test Read Retest. Drive should be replaced. That makes me think that this could be a bug in WD app. http://forumyaren.com/error-code/wdc-error-code-0223.php

An interrupt command to perform a specific task failed to complete. Re-test Drive 140 DRQ TIMEOUT ECC The drive did not properly respond to test commands. ThemeWelcome · log in · join Show navigation Hide navigation HomeReviewsHowChartsLatestSpeed TestRun TestRun PingHistoryPreferencesResultsRun StreamsServersCountryToolsIntroFAQLine QualitySmoke PingTweak TestLine MonitorMonitor GroupsMy IP isWhoisCalculatorTool PointsNewsNews tip?ForumsAll ForumsHot TopicsGalleryInfoHardwareAll FAQsSite FAQDSL FAQCable TechAboutcontactabout uscommunityISP acrufox 2011-03-15 11:22:37 UTC #6 Can this be used to RMA the drive?

Western Digital Error Codes

Replace the drive if the error repeats. Replace Drive 216 10+ IDNF Errors Identified Data Not Found (IDNF) 10+. to report if a drive has failed, it must be enabled as a system option.

This error occurs when the drive could not read Track Zero. If ECC occurs, use Data Lifeguard repair option for additional error correction. Replace Drive 456 IDNF 1 Identified Data Not Found. Replace Drive 214 10+ DAM Errors Data Address Mark (DAM) 10+.

Good luck. · actions · 2010-Oct-18 11:05 pm · Forums → Tech / Special Interest → Computer Hardware Help« Dell GX280 - On power-up psu fan revs crazy but no Western Digital Error Code 0007 After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 00 00 00 00 40 Commands leading to the Replace the drive if the error repeats. Go Here What's this I hear about First Edition Unix being restored?

Replace the drive if the error repeats. Conveyance self-test routine recommended polling time: ( 5) minutes. If the automatic repair feature is unable to repair these errors, replace the drive. Should I just use an old one from before the failure, or should I try to create a new one now, even though the disk may be corrupt? 4b)Or is there

Western Digital Error Code 0007

Update: S.M.A.R.T. === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WCAV******** LU WWN Device Id: 5 0014ee 259379483 Firmware Version: find more Track 0 on the drive must be accessed to perform parts of various internal tests. Western Digital Error Codes Replace the drive if the error repeats. My System Specs OS W7 Pro x64 CPU AMD|A64 X2 5400+ 2.8G Motherboard ASUS M3A78-EM AM2+ 780G Memory 1Gx2|OCZ DII1066OCZ2N10662GK R Graphics Card onboard Radeon 3200HD Sound Card M-Audio Revolution 7.1

This may be due to a media error. see here BSOD Help and Support Our Sites Site Links About Us Find Us Vista Forums Eight Forums Ten Forums Help Me Bake Network Status Contact Us Legal Privacy and cookies Windows 7 Retest. Several instances of information on data positioning and location could not be found.

Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Several instances of information on data positioning and location could not be found. No, create an account now. this page In other words, all of us, all of the time, are using partially defective disks.

Replace the drive if the error repeats. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Use the appropriate version.

Re-Test Drive with latest diagnostic utility 117 Uncorrectable ECC Error Uncorrectable Error Correction Code (ECC) Error.

This error can occur on non-Western Digital drives. Replace the drive if the error repeats. Integer function which takes every value infinitely often more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback moon1 2011-03-15 13:38:52 UTC #11 any time;) acrufox 2011-03-21 15:34:54 UTC #12 Interesting.

To fix it I just used my Windows 7 install CD and it was fine, until whenever it'd happen again. Self-Monitoring, Analysis, and Reporting Technology (SMART). Replace Drive 585 Busy Timeout During a read verify, a command could not be completed. Get More Info Continue to test or exit the test.

Re-Test Drive 18 Read Verify Sector Ext Error A Read Verify Sector Ext command during the test has failed. Short self-test routine recommended polling time: ( 2) minutes. According to to western digital's site: 223 Errors Repaired Errors found, but have been repaired successfully. May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable.

If a sector in a critical position fails (there are linked lists on any HDD), most if not all of the data on the entire disk will essentially be lost, or Retest the drive with Data Lifeguard. Please ensure that you are using the appropriate version of diagnostic utility. The drive should now be defect free.

I decided to perform a extended test. I even went further testing with HDTune. At this moment, the spare pool sector is re-mapped to appear as occurring in the logical sequence at precisely the same spot as the de-commissioned sector. At this point I decided to load up crystaldiskinfo, and the drive in question was highlighted as caution.В  Current pending sectors was at 8 and uncorrectable sector count was at 5