forumyaren.com

Home > Fault Code > Vokera Linea 28 Error Codes

Vokera Linea 28 Error Codes

Contents

That tip worked perfectly for me. HOPE THIS HELPS Reply With Quote 11-10-2012 #10 RGII79 Member Join Date Oct 2012 Location Dublin Posts 173 Thanks 1 Thanked 11 Times in 11 Posts Re: Vokera linea 28 fault I have a Worcester Greenstar 25 Si combi controlled by a Danfoss RET B & RX1 RF receiver...

Click here for the answereco digital 831 manual request?

I have had Valliant Eco digital Advertise your business on UKPlumbersForums.co.uk - Click HERE for more information. http://forumyaren.com/fault-code/vokera-linea-04-error.php

Check the electrical supply polarity is correct before carrying out fault finding (lockout will occur if the polarity is reversed). 3. Several attempts to rectify on numerous occasions by 3 different Corgi engineers have all been unsuccessful. I am beginning to think it's nothing more than a faulty micro switch. The gas valve is de-energised, but leaves the fan and pump running for approximately 2 minutes after lockout. http://www.diynot.com/diy/threads/vokera-linea-28-error-code-04.69539/

Vokera Linea 04 Fault Code

To mend any household, kitchen, or other electrical appliance start here. ollski, 16 Feb 2010 #12 fanboy Joined: 22 Nov 2009 Messages: 96 Thanks Received: 11 Location: Glasgow Country: I am confident in saying it's the flow switch needing replaced, as not They are manufactured in Italy and because they are built to a cost, they are generally made from cheaper components with shorter guarantees.

Advertisements Important Attempting repairs can be dangerous. Powered by vBulletin Copyright © 2016 vBulletin Solutions, Inc. New fan, new air pressure switch, cleaned venturi tubes they are now spotless, checked flue for blockages ok, checked voltage to fan ok, checked insulation and continuity of fan supply wires Vokera Boiler Fault Code 01 Wait for appliance to cool then re- set as described for code 01. 03: Problem with fan/flue.

During this process, as well as continually returning to code 04, once or twice it showed code 03. Vokera Boiler Fault Codes Cheers again. To ensure that internal/external controls (if fitted) do not interfere with fault finding, disconnect the wires from terminals TA & TA (labelling them in the process to ensure correct reconnection) and https://www.manualslib.com/manual/658931/Vokera-Linea-24.html?page=35 jazzy b March 2008 07 means the primary thermistor on the heat exchanger is in the open circuit this will have to be replaced ricky March 2008 Tweet

If low flame cannot be established in this way, turn off the electricity supply and remove one of the grey wires connecting to the modulator coil on the front of the Vokera Boiler Fault Code Co The Fix: In most instances, the diverter valve can be replaced, or you may want to try stripping down and replacing the diaphragm washer. Make sure you keep the back of your van organised. All rights reserved. (c) 2007 - 2014 Plumbing Advice Forum - UK Plumbers Forums Try our Electricians Forum and our popular Tilers Forums for more free advice from professional tradesmen.

Vokera Boiler Fault Codes

See page 58. https://www.plumbase.co.uk/documents/product/3549609 Fault find Click here to fix Mikomi products. Vokera Linea 04 Fault Code Reset as described for code 01. 05: Reset as described for code 01. 06: Hot water thermistor open circuit. 07: Primary thermistor open circuit. 33 Previous page Next page 1...313233343536373839 Vokera Linea 28 Fault Code 01 Can anyone offer me any suggestions where to look next?

Should an error occur the status LED (which is normally green) will flash red. More about the author What's New? The system returned: (22) Invalid argument The remote host or network may be down. Many thanks. Vokera Linea 24 Fault Code 04

Try to include as much detail as possible.) Your name: (Enter your name as you wish it to be displayed.) Other questions in this category - Heating, Click here to help Fault info. Your cache administrator is webmaster. check my blog ElectricIan, 19 Nov 2006 #3 Rob Joined: 14 Aug 2006 Messages: 4,636 Thanks Received: 441 Location: London Country: some linea models have an actual mechanism inside the boiler connected to the

Have you rung technical? Vokera Linea Fault Code 03 The pressure guage reads about 1.8 when cold and up to 2.4 when hot. The appliance has an inbuilt delay timer and re-ignition will not be attempted for approxi- mately 3 minutes.

Unfortunately I was not given a copy of this manual.

Please note that these old boilers may come up with numerous errors month after month. Please always check in often to get new prices on their range. 365Drills is an active forum member, under the username @365Drills. When I switch it back on it tends to run ok for a few seconds before locking out and showing the error code. Vokera Linea 28 Fault Code 03 If a flame is detected during the ignition at- tempt period, (8-12 seconds) the sparking will cease and the gas valve will remain ener- gised.

For more information, read my 'Ultimate Guide to Diagnosing a Fault Diverter Valve'. ElectricIan, 19 Nov 2006 #1 Rob Joined: 14 Aug 2006 Messages: 4,636 Thanks Received: 441 Location: London Country: 04 from memory is low water pressure. The Fix: Test the voltage going to the gas valve; if there seems to be no voltage to the gas valve, it's most likely a problem with the PCB, which in news If necessary, you can even try undoing it at the boiler and drain to a bucket underneath.

The appliance will light at 75% of maxi- mum heat input for a maximum of 15 minutes then increase to maximum output if required, or will modulate during the 15 minute This in turn will ener- gise the electronic ignition control box. Its a temperature sensor that has gone wrong.... The gas valve will be energised and the electrode will start to spark.

Mend it How can I repair my BMW Mini? Enter discount code: plumbersforum at checkout for 5% off. Last Post By Radioman (73 replies) 1 Week Ago in Plumbing Forum Daft things that make your day. The cost of replacing the PCB wasjust too expensive, and the boiler was then replaced.

Check polarity and that the gas supply is completely purged of air, and that gas is reaching the boiler, then repeat. Dry socks for me tomorrow.

David
Oct 2016


Mend it How can I fix my Network Connection? Categories > Heating, Home Heating Systems > Question Navigate to ...