forumyaren.com

Home > File Status > Vsam Close Error

Vsam Close Error

Contents

An attempt was made to access a relative-record file with an access type other then keyed or control interval. The combinations of possible values and their meanings are shown below. PROGRAMMER ACTION: Change the reset specification and rerun your job. Not enough programmer logical units for this partition. http://forumyaren.com/file-status/vsam-39-error.php

PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened. You can use the Access Method Services DELETE command to explicity clean up the file or you can rerun you job retry the implicit delete. Merge the processing that was two ACBs so that only one ACB is required. (However, this can result in error code X'14' when the same situation occurs.) Run both ACBs under If the problem persists print the dump from the SYSDMP. (Refer to VSE/VSAM Access Method Services Logic for ivterpretation of the IDUMP output.) Contact your IBM Support Center and make IDUMP

Vsam Return Codes

PROGRAMMER ACTION: IF the file was explicitly defined, you must change your program to be compatible with the files, change the file by explicitly deleting it and redefining it to agree X'07' 007 Return Code=04 Action=CBMN The referenced EXLST does not contain an entry for the exit you specified in M0DCB or SHOWCB. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. If you have any questions, suggestions, comments or feedback please call or send an e-mail to: [email protected] We appreciate hearing from you.

Both KEY and ADR/CNV access were specified in an ACB being opened for a share option 4 output file. It is provided "AS IS" without any expressed or implied warranty, including the implied warranties of merchantability, fitness for a particular purpose and non-infringement. You can check them in the same way that you check VSAM files. Vsam File Status 93 The second character is known as status-key-2 additional detail.

If the request was a GET, the record (or as much of it as possible) was moved to the user's work area. PROGRAMMER ACTION: Ensure that your program provides a properly generated ACB and does not inadvertently overlay the ACB, AMBL, AMDSB(s), or OAL before closing the ACB.

Return Code=04 Action=CBMN The GENCB Rerun the original job. https://www.ibm.com/support/knowledgecenter/SSLTBW_2.2.0/com.ibm.zos.v2r2.idat300/x1e.htm X'73' 115 Return Code=08 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a severe catalog error.

If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center. Vsam File Status 97 Rerun the original job. PROGRAMMER ACTION: Probable job control error. Either: Delete obsolete files occupying data space with matching classes (CLASS, USECLASS parameters) Define additional data space(s) of the required class on any of the volumes Using the ALTER command ADDVOLUMES

Vsam File Status 39

If the problem persists, save the job stream and take a system dump before contacting your IBM Support Center. http://ibmmainframes.com/references/a27.html The previous time the file was opened was the initial load of the file, and SPEED was specified. Vsam Return Codes Return Code=08 Action=Request Invalid or conflicting RPL options or parameters: SKP together with BWD. File Status 37 In Vsam An OPEN statement is successfully executed but the referenced optional file is not present at the time the OPEN statement is executed.

We are providing the... navigate to this website Once the fee is received by SimoTime the latest version of the software, documentation or training material will be delivered and a license will be granted for use within an enterprise, Save the dump you obtain and the SYSLOG output for later problem determination. X'88' 136 Return Code=>0 Action=CLOSE VSAM could not obtain a contiguous area of virtual storage large enough for the work area needed by the CLOSE routine. Vsam File Status 92

Codes beginning with a '1' are considered "at end" messages, those beginning with a '2' are considered "invalid key" messages, File Status Codes beginning with a '3' are considered "Permanent Errors", Return Code=0C Action=Request VSAM failed to read sequence-set records of an index. An entent block is not available in the system (temporary assignments use these) The device on which the volume is mounted is reserved (Attention Routine VOLUME command). More about the author An EXTENT statement is required for each volume to be accessed; for example, for each volume on which your base cluster and alternate index(es) reside.

Following are the common file status codes with their description which will help you to resolve the issues: CodeDescription 00Operation completed successfully 02Non-Unique Alternate Index duplicate key found 04Invalid fixed length File Status In Cobol Example The following may be helpful for problem determination. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

If you do not use simplified job control, use LISTCAT output to determine which volumes must be described in the EXTENT statements.

We specialize in the creation and deployment of business applications using new or existing technologies and services. The value is placed in the status key before execution of any EXCEPTION/ERROR declarative or INVALID KEY/AT END phrase associated with the request. X'22' 034 Return Code=08 Action=OPEN The volume serial number(s) specified in the EXTENT statement(s) do not match those recorded in the catalog entry. Vsam File Status 90 PROGRAMMER ACTION: Make sure the file-id in your DLBL statement does not specify the name of a default model.

We appreciate hearing from you. Return Code=08 Action=OPEN OPEN found an invalid control block structure for this ACB. Comments or Feedback This document was created and is copyrighted and maintained by SimoTime Technologies. click site If you do not want to install the VSE/VSAM Space Managment for SAM Feature, change the DLBL statement to specify a file other than SAM ESDS and rerun your job.

PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly assign device to accommodate the volumes required for the cluster and its associated alternate indexes. If the file was implicitly defined, you can cause open to implicitly DISP = NEW. Return Code=08 Action=Request No record found. If you do not use simplified job control, use LISTCAT output to determine which volumes must be described in the EXTENT statements.

You may, however, open the file for input. Return Code=08 Action=Request For SHAREOPTIONS(4), the file size is too large for the control area size. Although the record is in the base cluster, VSAM cannot find it because the pointer to it is missing. You requested a programmer logical unit that was not system generated (IOTAB xxPRG).

GET UPD ADR is requested but ADR was not specified on the ACB when the SHAREOPTIONS(4)KSDS was opened. Save the dump you obtain for later problem determination. IDUMP output Storage dump of the supervisor lock tables A dump of the lock file if one was specified at IPL SYSLOG output job stream X'FF' 255 Return Code=>0 Action=CLOSE An If records were added, deleted, or update, consult the explanation to message 42251.

X'14' 020 Return Code=04 Action=CBMN STRMAX or TRANSID were specified, but LSR was not specified in the ACB. This condition indicates that an attempt has been made to write beyond the externally defined boundaries of a sequential file. PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center, and have the dump output, SYSDMP output , and a copy of the job stream available for problem determination.