forumyaren.com

Home > File Status > Vsam Read Error 92

Vsam Read Error 92

Contents

Explore The ASCII and EBCDIC Translation Tables. The intent is to provide changes as the need arises and in a timeframe that is dependent upon the availability of resources. either in a "loop" or you will eventually do a START which gets EOF and then you do a READ = logic error. DISPLAY FS. http://forumyaren.com/file-status/vsam-read-error-02.php

DISPLAY FS. ENVIRONMENT DIVISION. Possible causes:Attempting to write beyond the externally defined boundaries of a file.Attempting a sequential WRITE operation has been tried on a relative file, but the number of significant digits in the Therefore, the file status key may not always be a numeric value that is easy to display. http://ibmmainframes.com/about43857.html

File Status 92 In Cobol

If you do the OPEN, and you get anything in the file status cod except 00 or 97, you need to stop your program IMMEDIATELY -- because your starts and reads Possible causes:For a READ statement the key value for the current key is equal to the value of that same key in the next record in the current key of reference.For CLOSE FILE1. Books on Vsam Vsam Manuals / Tutorials VSAM error code, VSAM file status, VSAM/QSAM status key, abend codes error code, file status, status key, VSAM open error, QSAM open error, VSAM

Explore the Assembler Connection for more examples of mainframe Assembler programming techniques and sample code. Therefore, the file status-key-2 may not always be a numeric value that is easy to display. The value indicates the status of that request. File Status 39 They appear on the JOB log. 004(04) Read past end of file 008(08) You attempted to store a record with a Duplicate Key, or there is a duplicate record for an

You can check them in the same way that you check VSAM files. PERFORM READ-SEQ UNTIL FLAG = 'N'. Refer to the section for Status-Key-1 being equal to "9" for additional information based on Status-Key-2. http://www.ibmmainframeforum.com/ibm-cobol/topic6265.html ie FD section.Make sure that it matches the listcat info of the vsam file. 2.

We appreciate hearing from you. Other possible causes are: 1. QSAM files (ordinary, sequential, flat files) can be made to return a code to you, if you wish. Alternatively a START or READ operation has been tried on an optional input file that is not present. 24 Relative and indexed files only.

Vsam File Status 92 While Writing

StatusKey-1Description by Group 0Successful Completion or non-terminal condition that may be acceptable to continue processing. If you use the sample code shown below, you will see the code in a variable in your program, which you then should test. File Status 92 In Cobol I want to conver that file from sequential to dynamic.. Vsam File Status 23 ACCEPT LOG.

VSAM and QSAM File Status Codes/keys from IBM manual Printout of SQLcodes for DB2, Version 7 SQLcodes SQLCODES for DB2 Version 8 from the IBM manual GC18-7422-0 04/06/05 Abend codes / navigate to this website Note:A SimoTime License is required for the items to be made available on a local system or server. Usually, it may come when file was not closed.           for example, Comments Sign in|Recent Site Activity|Report Abuse|Print Page|Powered By Google Sites The American Programmer Home Books on Mainframe Programming check the access mode in file declaration. Vsam File Status 35

OPEN INPUT FILE1. This can also happen when a sequential file is open for input and an attempt is made to open the same file for output.(Run Time System (RTS) message by Micro Focus). The first character of the File-Status-Key is known as status-key-1 and defines a group or category. More about the author We have made a significant effort to ensure the documents and software technologies are correct and accurate.

Actually VSAM file is Sequential, and I have defined in the program as DYNAMIC. This is usually caused by a conflict with record-length, key-length, key-position or file organization. ermanent I/O Error ermanent I/O Error - Record outside file boundary PEN, but file not found PEN with wrong mode ried to OPEN a LOCKed file PEN failed, conflicting file attributes

once you do a start on the VSAM file, you just read and display until end-of-file.

The Recording Mode is Variable or Fixed or not defined the same as when the file was created. 3. Open Error Code 39 by jellypuno » Thu May 02, 2013 9:40 am 9 Replies 2511 Views Last post by Robert Sample Thu May 02, 2013 4:32 pm 0C7 Error (System Robert Sample Global moderator Posts: 3100Joined: Sat Dec 19, 2009 8:32 pmLocation: Bellevue, Iowa Hasthanked: 1 time Beenthanked: 177 times Top Re: i get logic error 92 when i run VSAM Logical error codes These codes indicate VSAM errors.

Make sure that the record being read into a layout is not smaller than the recod. 3.If you are using a START verb to read a record directly, you first need The SimoTime name or Logo may not be used in any advertising or publicity pertaining to the use of the software without the written permission of SimoTime Technologies. For the COBOL environment if the FILE STATUS clause is specified in the FILE-CONTROL entry, a value is placed in the specified status key (the 2-character data item named in the click site PERFORM UNTIL FLAG = 'N' READ FILE1 NEXT AT END MOVE 'N' TO FLAG END-READ DISPLAY BK SPACE FS END-PERFORM.

Whether you want to use the Internet to expand into new market segments or as a delivery vehicle for existing business functions simply give us a call or check the web CLOSE FILE1. The value is placed in the status key before execution of any EXCEPTION/ERROR declarative or INVALID KEY/AT END phrase associated with the request. MAIN-RTN.

Therefore, adjustments may be needed to execute the jobs and programs when transferred to a system of a different architecture or configuration. Please -- start at the beginning and tell us what you are attempting to do in plain English without any code involved. WORKING-STORAGE SECTION. 01 ACC. 02 ACCNO PIC X(10). 02 YEAR PIC X(4). If you don't check the code when dealing with QSAM files, the system abends your program in case of serious error, and gives you a system completion code.

Indicates a sequence error. You have reached the end of the file. 12 Attempted to open a file that is already open. 13 File not found. DISPLAY BK SPACE FS. A good place to start is The SimoTime Home Page via Internet Connect for access to white papers, program examples and product information.

i got the output...the mistake was not in code but the way i loaded the data in ksds... it appears you are attempting to use one file where you need two files (sequential log file and indexed VSAM file).3. We reserve the right to make changes without notice at any time. Following are the common file status codes with their description which will help you to resolve the issues: CodeDescription 00Operation completed successfully 02Non-Unique Alternate Index duplicate key found 04Invalid fixed length

This document may be used to assist as a tutorial for new programmers or as a quick reference for experienced programmers. the VSAM KSDS file is defined with a key and nothing else -- you could easily get a 92 file status if there is more data in each record than your